camshaft造句

1、The isothermal quenching process of the ductile iron camshaft was analyzed.
对球铁凸轮轴的等温淬火工艺进行了分析。

2、One centrally located camshaft per cylinder bank is driven by a fiberglass-reinforced toothed belt.
一个位于中央的每缸银行是由凸轮轴驱动的玻璃纤维增强型齿形带。

3、When you increase the RPM, however, this configuration for the camshaft does not work well.
当您增加转速时，但这种配置的凸轮轴不工作。

4、The camshaft has a cam, on which there is a lob, or bump.
凸轮轴上有一个凸轮，凸轮上有一个凸角。

5、The key technology of hollow assembled camshaft is joint between the shaft and the cam lobes.
中空装配式凸轮轴的技术关键为凸轮和轴体之间的连接。

6、The eccentric may be part of the camshaft itself or may bolt to it.
偏心轮可能与凸轮轴是一体的，也可能是通过螺钉连接的。

7、Rocker arm, Rocker arm shaft, Rocker assembly, Valve guide tube, Camshaft bearing Cap.
气门摇臂，摇臂轴，摇臂总成，气门导管，凸轮轴盖。

8、It's connecting methods are the key technology in assembling camshaft production.
而其连接方法是装配式凸轮轴制造的关键技术。

9、Camshaft is one of the important parts on the automobile engine.
凸轮轴是汽车发动机的重要零件。

10、Calculation of Heat Balance during Mold Filling for Hollow Camshaft in EPC
消失模铸造空心凸轮轴充型过程中热平衡计算

11、Applied to ductile iron crankshaft, camshaft and other parts of the grinding and other grinding.
适用于球墨铸铁曲轴，凸轮轴等工件的磨削及其它磨削。

12、The camshaft has a cam, on which there is a lob, or bump
凸轮轴上有一个凸轮，凸轮上有一个凸角。

13、The manganate phosphating technology of camshaft is introduced.
介绍凸轮轴的磷化工艺。

14、In its initial stage the change-of the camshaft is performed.
在他的初始阶段凸轮轴的转换被执行。

15、Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸轮轴固定螺栓，并拆去作为一个总成的链轮和链条。

16、The camshaft also fits inside the block, except on overhead-cam engines.
除了顶置凸轮（OHC）发动机以外，凸轮轴都安装在气缸体里面。

17、Install cover for camshaft housing.
安装凸轮轴室盖。

18、Analysis on Mold Filling of Hollow Camshaft in EPC
气化模铸造空心凸轮轴的充型过程分析

19、Since 1958, an engine with a single overhead camshaft has been used.
从1958年起，便已使用带有单顶置凸轮机的发动机。

20、Camshaft from the crankshaft through the timing belt or gear or chain drive.
凸轮轴由曲轴通过齿形带或齿轮或链条驱动。

21、Therefore, the camshaft must revolve at exactly half the speed of the crankshaft.
因此，凸轮轴必须以曲轴正好一半的速度旋转。

camshaft翻译