plunger造句

1、The plunger consists of a solid spiral mandrel, tapered mandrel nose, and premium high-alloy dart.
该柱塞包括一个实心螺旋轴、锥形芯轴的机头和优质高合金活门。

2、One that dashes, especially the plunger of an ice-cream freezer.
猛冲者猛冲的人或物，尤指冰淇淋凝固搅拌器

3、Craft of DW-series Single Hydraulic Prop′s Plunger Piece Weld
DW型单体液压支柱柱体焊接工艺

4、The balance valve circuit is to support the weight of platen and plunger design.
回路中的平衡阀是为支撑压板及柱塞的重量而设计的。

5、Plunger head chute different location, change the amount of oil in a different manner.
柱塞头部斜槽的位置不同，改变供油量的方法也不同。

6、When the plunger diameter is decreased, what happens to the fill time?
当冲头的直径减少，填充时间会发生什么变化？

7、Cock and ball: Turn off the prop is a plunger or a ball, rotating around its own axis.
旋塞和球形：关闭件是柱塞或球，围绕本身的中心线旋转。

8、The most common type USES spring tension and pressure against a plunger to maintain the pressure.
最常用的一种回压阀使用弹簧张力和对柱塞的压力来保持压力。

9、The plunger or piston of a force pump or hydraulic press.
活塞压力泵或水压机内的柱塞或活塞

10、Figure 1 shows the various seals and traveling valve in the plunger position.
图1所示是各种密封和游动阀在柱塞上的位置。

11、The solenoid plunger pulls the vent valve down, blocking off the passage to the charcoal canister.
电磁柱塞拉下通气阀，堵住通向活性碳罐的通路。

12、This is often tail - fin shape plunger due to excessive thickness.
这往往是柱塞尾部翅形体过厚所致。

13、The radiated sound field of ring plunger is analyzed.
研究了环状活塞声源辐射声场的特性。

14、With the car upside - down, the ball forces the plunger to seat against the guide plate.
当汽车倾倒时，滚珠迫使柱塞落在支承板上。

15、The plunger should be withdrawn from sleeve.
柱塞应从套筒里抽出来。

16、This would free the spring, and up would pop a plunger to announce the bird was ready.
这样弹簧就可被释放并向上弹出一个活塞以宣告鸟类已经烤熟。

17、G. Slowly advance the needle while gently withdrawing the plunger of the syringe.
在轻轻回抽注射器的同时缓慢进针。

18、The plunger or piston of a force pump or hydraulic press
活塞压力泵或水压机内的柱塞或活塞

19、The position of the plunger cylinder is measured by a linear position transducer.
活塞杆的位置是通过一个线性位置传感器测量的。

20、Failure Analysis of the Plunger of Plunger Pump OPI-1800AWS
OPI-1800AWS柱塞泵柱塞失效分析

21、The plunger extruder is developed for suiting to process UHMWPE pipes, rods and profiles, etc.
研制了适于加工UHMWPE管材、棒材及异型材等制品的柱塞式挤出机。

22、R2 is the point of signal transfer between plunger and barrel.
R2是顶针与套壳体之间的信号传输点。

23、Turn off the prop is a plunger or a ball, rotating around its own axis.
关闭件是柱塞或球，围绕本身的中心线旋转。

24、Rubber plunger should not be rubber thread, rubber chipping, foreign impurity, spray frost.
橡胶活塞应无胶丝、胶屑、外来杂质、喷霜。

plunger翻译